|
|
|
HOME > ±â¼úÀÚ·á> °ü·Ã³í¹® |
|
|
|
|
|
|
|
[Priceision Engineering (¹Ì±¹/SCIE)] Experimental investigation on CO2 laser-assisted micro-slot milling characteristics of b¡¦ |
±Û¾´ÀÌ : °ü¸®ÀÚ
Á¶È¸ : 2053
|
|
Æ®·¢¹é ÁÖ¼Ò : http://sharp-eng.com/web/bbs/tb.php/group_02_b_03/196
|
https://www.sciencedirect.com/science/article/pii/S0141635919307469?ca¡¦ (4589) |
|
ÇмúÁö¸í: Precision Engineering
¹ßÇà±¹°¡: ¹Ì±¹
¹ßÇ¥ÀÏÀÚ: 2020³â 2¿ù
SCI¿©ºÎ : SCIE
¿ø¹®Link: https://www.sciencedirect.com/science/article/pii/S0141635919307469?casa_token=KdxnV5bwZxsAAAAA:6sVQE3k_LRawqEUN8If5n7lujeMC2iD22XFmSsttR0C52fcPSyd7cjapBMaHlGLD2JBPmx5vU9NB
Á¦¸ñ: Experimental investigation on CO2 laser-assisted micro-slot milling characteristics of borosilicate glass
ÀúÀÚ: ±èÅ°â(»ï¼ºÀüÀÚ) ±Ç±Í°¨(¼¿ï´ëÇб³) ÁÖÁ¾³²(¼¿ï´ëÇб³) ¼Û±â¿µ(»þÇÁÁ¤¹Ð)
³»¿ë: ·¹ÀÌÁ®ÀÇ ¿¿¡³ÊÁö¸¦ ÀÌ¿ëÇÏ¿© À¯¸®¸¦ ¿£µå¹Ð·Î Àý»è°¡°øÇÔ
ÃÊ·ÏAbstract: Demands for micro-machining on glass have been increasing in various industries due to the unique properties of glass, such as transparency or biocompatibility. However, micro-channel fabrication on glass with high precision has been challenging due to its brittle characteristics. This research presents the CO2 laser-assisted micro-milling process and investigates the machining characteristics experimentally. Micro-channels without cracks were fabricated using micro-end mill and CO2 laser irradiation as an assisting heat source. Compared to the process without laser heating in the same matching conditions, the average surface roughness was reduced by 96%, and cutting force was reduced by 28% and 66% for the feed and thrust direction, respectively. Continuous and sheared chips were observed with laser heating, indicating the process is in ductile-regime machining. Through the investigation of machining parameters, it was found that micro-channels with low average surface roughness can be achieved at the proper laser power when the workpiece is heated up to the strain point at tool position, at low feed rate, and at high axial depth of cut, as long as the tool withstands the cutting forces. Consequently, it can be concluded that it is possible to increase the material removal rate in micro-milling of borosilicate glass with high quality by using the CO2 laser, which was found to be an effective and suitable heating method.
|
|
|
|
|
|